signal conditioning modules t e x x xx c n series 201 6 . 07.15 - a/1 page 1 of 3 m ornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation active high precision signal conditioning module rohs features ? two- port isolation (signal input and signal output) ? high accuracy (0.1% f.s.) ? h igh linearity (0.1% f.s.) ? isolation voltage (2kvac/60s) ? low ripple & noise : ( 35mvpp, 20mhz) ? extremely low temperature coefficient ( 50 ppm/ ) ? operating temperature range: -40 to + 8 5 ? compact size : dip18 (26*9.5*12.5mm) ? esd protection (iec/en61000-4-2 contact 4kv perf. criteria b) part number system c n p a c k a g e p o la r it y s i g n a l i n p u t , d u a l p o l a r i t y s i g n a l o u t p u t p s s i is o la t i o n p o w e r o u t p u t o w e r s u p p l y i g n a l o u t p u t i g n a l in p u t s o la t i o n a m p l i f ie r d u a l t e x x x x texxxxcn series is analog signal isolation modules with front-end positive/negative voltage signal input and rear-end positive/negative voltage signal output. they are equipped with built-in efficient micro-power source and can supplying power to the internal circuit of t he product. the product adopts the electromagnetic isolating technology as a substitute for the traditional linear opto-isolator. in contrast, this type of product has a better performance in temperature drift, linearity, low power consumption and low ripple. they are two -terminal isolation (power input and the signal output are on the common ground. isolated between signal input terminal and signal out put terminal) . selection guide m odel power supply input typ. (vdc) input signal output signal isolation p ower o utput (vdc) te5540cn 15vdc 10v 10v none TE5550CN 12vdc 10v 10v none te6640cn 15vdc 5v 5v none te6650cn 12vdc 5v 5v none notes: customization products are available if required. input specifications item operating conditions min. typ. max. unit power input input voltage - 5 % ( nomi nal value) nominal value + 5 % ( nomi nal value) vdc input power signal full load -- -- 1.0 w signal input input signal reference s election g uide input impedance in case of max. input of voltage signal 10 -- -- m overload maximum continuous over range -15 -- +15 v output specifications item operating conditions min. typ. max. unit output signal output signal reference s election g uide load capacity voltage output 2 -- -- k ripple & noise* 20mhz bandwidth -- -- 35 mvp-p transmission specifications item operating conditions min. typ. max. unit signal precision ta=25 -0.1%f.s. -- +0.1%f.s. -- power regulation (typ. value of power supply input) 5% -0.05%f.s. -- +0.05%f.s. -- load regulation change between no-load and full load 2k ~ -0.05%f.s. -- +0.05%f.s. -- temperature coefficient operating temperature range of -40 to +85 -- -- 50 ppm/ bandwidth 2 -- -- khz response time -- -- 1 ms package dual polarity signal input dual polarity signal output isolation power output power supply signal output sig nal i nput isolation amplifier
signal conditioning modules t e x x xx c n series 201 6 . 07.15 - a/1 page 2 of 3 m ornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation general specifications item operating conditions min. typ. max. unit electric isolation power input and the signal output are on the common ground. isolated between signal input terminal and signal out put terminal . isolation voltage t esting for 1 minute, leakage current <1ma, humidity <70% 2 -- -- kvac insulation resistance 500vdc 100 -- -- m operating temperature -40 -- +85 transportation and storage temperature -40 -- +85 casing temperature rise ta=25 -- -- 30 application environment the presence of dust, fierce vibration,impulsion and corrosive gas may cause damage to the product. physical specifications casing material black flame-retardant and heat-resistant plastic package dip18 weight 5.8 g(typ.) cooling method free air convection emc specifications ems esd iec/en61000-4-2 contact 4kv perf. criteria b eft iec/en61000-4-4 signal input port 1 kv (see fig. 2 for recommended circuit) perf. criteria b surge iec/en61000-4-5 signal input port 1kv(line to ground) (see fig. 2 for recommended circuit) perf. criteria b application precautions 1. please read the instructions carefully before use; contact our technical support if you have any problem; 2. do not use the product in hazardous areas; 3. u se dc power supply for the product and 220v ac power supply is prohibited; 4. do not dismount and assemble the product without permission to avoid failure or malfunction of equipment; 5. unless otherwise specified, parameters in this datasheet were measured under the conditions of ta=25 , humidity<75% with power input nominal voltage and rated signal output full load . a fter-sales service 1. e x-factory inspection and quality control have been strictly conducted for the product; if there occurs abnormal operation or possibility of failure of internal module, please contact the local representative or our technical support ; 2. t he warranty period for the product is 3 years as calculated from the date of delivery. i f any quality problem occurs under normal use within the warranty period, the product can be repaired or changed for free. a pplied circuit see application notes for isolated transmitter for details. design reference 1. wiring diagram for product application fig. 1 notes: nc: no t available for electrical connection
signal conditioning modules t e x x xx c n series 201 6 . 07.15 - a/1 page 3 of 3 m ornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation 2. emc solution-recommended circuit fig. 2 components recommended parameters r1 12 /2w tvs1 smbj 1 5 c a 3. for more informati on please find the application notes on www.mornsun-power.com dimensions and recommended layout notes: 1. packing information please refer to 'product packing information'. packing bag number: 58240002; 2. all index testing methods in this datasheet are based on our company s corporate standards; 3. the performance indexes of the product models listed in this datasheet are as above, but some indexes of non-standard model products will exceed the above-mentioned requirements, and please directly contact our technician for specific information; 4. we can provide product customization service; 5. specifications of this product are subject to changes without prior notice. mornsun guangzhou science & technology co., ltd. address: no. 5, kehui st. 1, kehui development center, science ave., guangzhou science city, luogang district, guangzhou, p. r. china tel: 86-20-38601850-8801 fax: 86-20-38601272 e-mail: info@mornsun.cn
|
